Brand: beko
Category: Vacuum Cleaner
Document Type: Manual
Language: EN
Manual for VRR 60314 VW
Uploaded: April 20, 2026, 8:03 p.m.
Warranty Information
This product comes with a 12-month breakdown and repair guarantee from the date of purchase.
Robot Vacuum Cleaner Operation Summary
Turning On/Off: Press and hold the power button (⌂) for 3 seconds.
Starting Cleaning: Short press the power button (⌂) to start automatic cleaning. The robot will clean in a "Z" route, then along walls, and then cover remaining areas before returning to the charging dock.
Pausing: Pressing any button will stop the robot. Press the charging button (⌂) to initiate automatic recharging.
Charging: Place the robot on the charging station, aligning communication pins. Charging begins when the indicator on the station turns off.
Spot Cleaning: Press the power button (⌂) twice to activate spot cleaning mode for a 1.5m diameter area.
Vacuum Power Selection: Use the mobile app to select cleaning power (Quiet, Standard, Powerful, Maximum).
Remote Control: Use the mobile app for manual remote control of the robot.
Sleep Mode: The robot enters hibernation if inactive for 10 minutes or switches to sleep mode after being fully charged for 10 minutes.
System Reset: Press and hold the power button (⌂) for 15 seconds in standby to reset the system.
Mopping: Install the mopping unit and set wetness level via the app. Do not use on carpets. Use only water or approved detergents. Remove the unit when charging or not in use.
Troubleshooting and error codes
| Voice Prompts | Solution |
|---|---|
| The robot cannot start. | - Make sure the robot is connected to power supply. - Make sure the battery is fully charged. - If the problem persists, please reset the robot. |
| The robot suddenly stops working. | - Check whether the robot is stuck or blocked by obsta-cles. - Check whether the battery is too low. - If the problem persists, please shut it down, wait for 3 seconds, and then restart it. |
| Cannot make a sweep schedule | - There are too many obstacles around the charging dock. Please place the charging dock to an area free of obstacles. - The robot vacuum cleaner is too far away from the charging dock. Bring the robot vacuum cleaner closer to the charging dock and try again. - Make sure that the charging stand station is plugged and there is energy. |
| Suction too weak | - Check the suction inlet for any obstruction. - Empty the dustbin. - Clean filters with water. - Check whether filters are wet due to water or other liq-uids on the floor. Let filters dry naturally thoroughly be-fore use. |
| Cannot charge the machine | - Please check whether the charging dock is correctly connected to the power supply, and the indicator light il-luminates when the power is on. - When the robot is normally connected to the charging dock, the indicator light extinguishes. - If the robot is connected to the charging dock, but the indicator light does not extinguish and the robot does not respond, please use a dry cloth to wipe the charging pole piece at the bottom of the robotic vacuum cleaner and the charging piece of the charging dock, and then try again. - If the robot still can not be charged after performing the above operations, please contact the after-sales depart-ment or your dealer. |
| The robot cannot return to the charging dock. | - Clear the charging dock of objects within 0.5m on the left and right sides and within 1.5m ahead. - Make sure that the robot starts sweep from the charg-ing dock without abnormal movement. - When the robot is near the charging dock, it can return faster. But if the charging dock is located far away, the robot will need more time to return. - Please wait during its return. - Clean charging electrodes. |
| The rolling brush does not rotate | - Clean the rolling brush. - Check whether the main brush and the main brush cov-er are installed correctly. |
| Abnormal action or sweep route of the robot | - Carefully clean the sensor with dry cloth. - Restart the robot. |
| No water released during mopping | - Make sure there is enough water in the water tank. - Check whether the mop module is installed correct-ly. Upon correct installation, you will hear related voice prompt. - Check whether the water outlet is blocked. |
| The machine cannot connect to your Wi-Fi network. | - Ensure that your Wi-Fi router supports 2.4GHz and 802.11b/g/n bands as this equipment does not support 5GHz bands. For more details, please refer to the "Faults in Wi-Fi Connection" section herein. |