Brand: Electrolux
Category: Cooktop
Document Type: Manual
Language: EN
Available Languages: EN , ES
Manual for 36" INDUCTION COOKTOP
Uploaded: Sept. 12, 2025, 4:17 a.m.
Warranty Information
Refer to your product documentation for specific warranty information.
Induction Cooktop Operation
Powering On/Off: Touch and hold the power button for 3 seconds to activate or deactivate the cooktop. The display will show '0' or the last used setting.
Selecting a Cooking Zone: Touch the desired cooking zone on the display.
Adjusting Power Level: Once a zone is selected, touch the 'Timer' key to cycle through power levels from 1 (Low) to 9 (High). The display will show the selected level.
Booster Function: Touch and hold the 'Timer' key to activate the 'Booster' function for maximum power (MAX). The display will show 'MAX'. Touch the 'Timer' key again to return to level 9.
Activating/Deactivating Demo Mode: Touch and hold the 'Enter/Edit Menu' key for 3 seconds to enter or exit Demo Mode. The display will show 'dEMO' when activated.
Troubleshooting and error codes
| ERROR CODES | UI Display | Error Description | Corrective Action |
|---|---|---|---|
| E0-XX Configuration | Wrong configuration of the induction module or user interface | 1. Disconnect power to the appliance for 30 seconds. If error still occurs: Replace the user interface. 2. If replacing the UI does not fix the error, replace the faulty induction module(s). | |
| E3-xx Power Supply | Over or under voltage | 1. Check 208-240 volt AC between L1 and L2 connectors. See the connection label on the bottom of the appliance. Operate the appliance with cookware for 1 min. 2. If the supply is okay, replace the faulty induction module(s). | |
| E4-xx Coils | Failure occurs after heating up an empty pan with level "MAX" or A pot has a large pan bow, which is causing an over temperature at the coil temperature sensor. The failure disappears after 15 min. | This is normal behavior. The reason for the over temperature is the air gap between the pot bottom and the ceramic cooktop, which causes the slower reaction time for the sensor. | |
| E4-xx Temp Sensor | Temperature sensor defect or wrong mounting. | 1. Check connector at induction module. 2. Check the coil sensor, it should be placed even in the silicon carrier. 3. For appliances with 3 zones, is the "Dummy" temperature sensor at the 2nd terminal mounted? 4. Replace coil with sensor. 5. If above is without success, replace the faulty induction module(s). | |
| E6-xx Power Module | Defective induction module | Disconnect the appliance from the mains for 30 sec. If error still occurs after 1 min operation, replace the faulty induction module(s). | |
| E7-xx Fans | Fan defect. | 1. Operate 1 zone on high power level for 1 min. Fan should start running. If not, check for blocking of fan and connector at induction module. 2. Replace fan. Attention: this is not possible on all induction modules. 3. If this is without success, replace the faulty induction module. | |
| E8-xx Communication | Communication/wiring between induction generator and user interface interrupted. Center wire of MACS connector defect OR no main power supply. (always if only both right zones with error) | 1. Check the power supply cable between the UI and the power board (BS003 connection on the power board to XP01 on the UI). 2. If the cables are unplugged or loose, reconnect. If the cables are damaged, replace cables. If cables good, then replace the power board. 3. If error persists, replace UI. | |
| E9-xx User Interface | User interface touch system defect. | Disconnect the appliance from the mains for 30 sec. If the alarm still occurs after 1 min of operation, replace the user interface. If the error still occurs, replace the UI carrier. |