Manual for EEG48300L

Manual for EEG48300L

Brand: ELECTROLUX

Category: Dishwasher

Document Type: Manual

Language: EN

Uploaded: Nov. 21, 2025, 7:21 p.m.

Warranty Information

Refer to the warranty card or service book for specific warranty information.

Dishwasher Operation Summary

Loading the Dishwasher: Always use the full capacity of the baskets. Arrange items as instructed to ensure optimal cleaning. Do not overload. Do not wash non-dishwasher-safe items like wood or pewter. Place hollow items with the opening downwards. Ensure spray arms can rotate freely.

Adding Detergent: Use dishwasher-specific detergent (powder, gel, or tablets). Follow dosage instructions on the packaging. For short programs, tablets may not dissolve fully. Ensure the detergent dispenser lid can open freely.

Selecting a Programme: Use the MY TIME bar to select a program based on duration and soil type. ECO offers the most efficient water and energy use. AUTO Sense automatically adjusts the cycle. Additional EXTRAS like ExtraPower or GlassCare can be activated.

Starting the Dishwasher: Ensure water tap is open. Close the door to start. The appliance will automatically switch off when not operating (Auto Off function).

End of Programme: The display shows 0:00. Auto Off activates. Ensure water tap is closed.

Troubleshooting and error codes

Problem and alarm code Possible cause and solution
You cannot activate the appliance.
  • Make sure that the mains plug is connected to the mains socket.
  • Make sure that there is no damaged fuse in the fuse box.
The programme does not start.
  • Make sure that the appliance door is closed.
  • If the delay start is set, cancel the setting or wait for the end of the countdown.
  • The appliance recharges the resin inside the water softener. The duration of the procedure is approximately 5 minutes.
The appliance does not fill with water. The display shows i10 or i11.
  • Make sure that the water tap is open.
  • Make sure that the pressure of the water supply is not too low. For this information, contact your local water authority.
  • Make sure that the water tap is not clogged.
  • Make sure that the filter in the inlet hose is not clogged.
  • Make sure that the inlet hose has no kinks or bends.
The appliance does not drain the water. The display shows i20.
  • Make sure that the sink spigot is not clogged.
  • Make sure that the interior filter system is not clogged.
  • Make sure that the drain hose has no kinks or bends.
The anti-flood device is on. The display shows i30.
  • Close the water tap.
  • Make sure that the appliance is correctly installed.
  • Make sure the baskets are loaded as instructed in the user manual.
Malfunction of the water level detection sensor. The display shows i41 - i44.
  • Make sure that the filters are clean.
  • Switch the appliance off and on.
Malfunction of the wash pump or the drain pump. The display shows i51 - i59 or i5A - i5F.
  • Switch the appliance off and on.
The temperature of the water inside the appliance is too high or malfunction of the temperature sensor occurred. The display shows i61 or i69.
  • Make sure that the temperature of the inlet water does not exceed 60°C.
  • Switch the appliance off and on.
Technical malfunction of the appliance. The display shows iC0 or iC3.
  • Switch the appliance off and on.
The level of water inside the appliance is too high. The display shows iF1.
  • Switch the appliance off and on.
  • Make sure that the filters are clean.
  • Make sure that the outlet hose is installed at the right height above the floor. Refer to the installation instructions.
The appliance stops and starts more times during operation.
  • It is normal. It provides optimal cleaning results and energy savings.
The programme lasts too long.
  • If the delay start option is set, cancel the delay setting or wait for the end of the countdown.
  • Activating options increases the programme duration.
The displayed programme duration is different than the duration in the consumption values table.
  • Refer to the consumption values table in the chapter "Programme selection".
The remaining time in the display increases and skips nearly to the end of the programme duration.
  • This is not a defect. The appliance is working correctly.
Small leak from the appliance door.
  • The appliance is not levelled. Loosen or tighten the adjustable feet (if applicable).
  • The appliance door is not centred on the tub. Adjust the rear foot (if applicable).
The appliance door is difficult to close.
  • The appliance is not levelled. Loosen or tighten the adjustable feet (if applicable).
The appliance door opens during the wash cycle.
  • The AirDry function is activated. You can deactivate the function. Refer to "Basic settings".
Rattling or knocking sounds from the inside of the appliance.
  • The tableware is not properly arranged in the baskets. Refer to basket loading leaflet.
  • Make sure that the spray arms can rotate freely.
The appliance trips the circuit-beaker.
  • The amperage is insufficient to supply simultaneously all the appliances in use. Check the socket amperage and the capacity of the meter or turn off one of the appliances in use.
  • Internal electrical fault of the appliance. Contact an Authorised Service Centre.
Privacy Policy