Manual for B22W-7 LED

Manual for B22W-7 LED

Brand: Fujitsu

Category: Monitors

Document Type: Manual

Language: EN

Available Languages: EN , ES

Uploaded: Nov. 21, 2025, 7:39 p.m.

Manual Publish Date: 2013-05-01

Warranty Information

Refer to the warranty booklet for details on the warranty.

Your LCD screen...

has a whole range of useful features and functions, e.g.:

  • TFT display (Thin Film Transistor; active matrix)
  • minimal space requirements thanks to slim casing
  • optimum ergonomic characteristics (totally distortion-free, excellent picture definition and colour purity right into the corners)
  • high degree of brightness and good contrast
  • high resolution (1680 x 1050)
  • presentation of up to 16.7 million colours (in conjunction with an appropriate display adapter)
  • automatic scanning of horizontal frequencies from 30 to 82 kHz and refresh rates (vertical frequencies) from 56 to 76 Hz (absolutely flicker-free)
  • Digital screen controller with microprocessor for storing 40 different display modes
  • freely adjustable colour alignment for matching the screen colours to the colours of various input and output devices
  • convenient operation via integrated OSD (On-Screen-display) menu
  • VESA-DDC compatibility
  • VESA-FPMPMI compatibility (Flat Panel Monitor Physical Mounting Interface)
  • Mounting device for swivel arm or a similar accessory
  • Plug&Play capability
  • digital video inputs (DVI and DisplayPort) with HDCP
  • power management for reducing power consumption when the computer is not in use
  • Compliance with the recommendations according to TCO 6.0
  • the monitor fulfills all GS ("Geprüfte Sicherheit", Certified Security) requirements.

This operating manual contains important information you require to start up and run your LCD monitor.

A graphics card (display adapter) with a VGA interface or a digital graphics card with a DVI or DisplayPort interface is required to control the LCD monitor. The monitor processes the data supplied to it by the graphics card. The graphics card or the associated driver software is responsible for setting the modes (resolution and refresh rate).

When putting the monitor into operation for the first time, the screen display should be optimally adapted to the display adapter used and adjusted in accordance with your needs (see chapter "Changing the monitor settings", Page 21).

Target group

You don't need to be an "expert" to perform the operations described here. Nonetheless, it is important to always observe the safety notes given in the operating instructions for the computer and in this manual.

In the event of any problems, please contact your sales office or our Service Desk.

Troubleshooting and error codes

Having this problem? Check the following points:
No screen display
Power indicator does not light up
  • Check whether the power cable on the monitor is connected correctly.
  • Check whether the computer is switched on.
No screen display
Power indicator is lit
  • Check whether the computer is switched on.
  • Check whether the data cable for the monitor is correctly attached to the monitor port on the computer.
  • Press any key on the computer keyboard. The computer may be in power saving mode.
  • Alter the brightness and/or contrast until you get a picture.
Message: No Signal
  • Check whether the data cable for the monitor is correctly attached to the monitor port on the computer.
  • Check whether the computer is switched on.
Message:
Frequency out of range:
## kHz / ## Hz
Please change the display mode
to 1680 x 1050 with 60 Hz
  • The input signal (horizontal frequency and refresh rate) at the displayed input does not correspond to the technical data for the monitor.
  • Adjust the video frequency range using the computer software (see documentation for the computer or display adapter).
  • Set a different screen resolution using the computer software (see documentation for the computer or display adapter).
Picture position not correct
  • The monitor recognises an undefined mode (see chapter "Technical specification", Page 33).
  • Press the AUTO button to conduct the auto-adjustment of the screen.
Picture is shaking
  • Check whether the data cable for the monitor is correctly attached to the monitor port on the computer.
  • Press the AUTO button to conduct the auto-adjustment of the screen.
Picture is wrongly adjusted
  • Run the Factory Recall function in the OSD menu. The Auto Processing message appears.
Picture disturbances (vertical lines)
  • Press the AUTO button to conduct the auto-adjustment of the screen.
Picture disturbances (horizontal lines, picture noise)
  • Press the AUTO button to conduct the auto-adjustment of the screen.
The screen becomes darker
  • The background lighting has a limited lifetime. If your monitor display should become too dark, the background lighting will have to be replaced.
  • Contact our Service Desk.
Privacy Policy