Manual for GTD65EBSJWS

Manual for GTD65EBSJWS

Brand: GE

Category: Dryer

Document Type: Manual

Language: EN

Available Languages: EN , ES

Uploaded: Nov. 21, 2025, 9:23 p.m.

Manual Publish Date: 2015-01-01

Warranty Information

GE will replace any part of the dryer that fails due to defects in materials or workmanship for one year.

Quick Start Guide

  1. Step 1: Clean lint filter.
  2. Step 2: Add clothes and shut door.
  3. Step 3: Select drying cycle.
  4. Step 4: Push Start.

Key Features

  • Power: Press to wake up the display or put the dryer into idle mode.
  • Start/Pause: Press to begin or pause the cycle.
  • Display & Status Lights: Shows time remaining, Pause, Controls lock, Sensing, and Clean Lint Filter status.
  • Control Lock: Press and hold Extended Tumble and - (minus) buttons for 3 seconds to lock/unlock controls.
  • Settings: Adjust Time, Level (dryness), and Temp (temperature) for sensor and timed cycles.
  • Drying Cycles: Options include Steam Dewrinkle, Steam Refresh, Sanitize/Anti-Bacterial, Bulky Items, Towels/Sheets, Cottons, Mixed Load, Casuals, Delicates, Speed Dry, Jeans, Timed Dry, Warm Up, and Air Fluff.
  • eDry: Available on select cycles to reduce energy consumption.
  • Extended Tumble: Provides 1 hour of no-heat tumbling to minimize wrinkles.
  • Damp Alert: Beeps when clothes are damp, ideal for hanging dry items.
  • Drum Light: Illuminates the drum when the door is opened or Damp Alert is activated.
  • Delay Dry: Set a delayed start time in 1-hour increments up to 24 hours.
  • Signal Adjust: Adjusts the volume of button presses and the end-of-cycle signal.
  • My Cycle: Remembers custom settings for specific knob selections.

Troubleshooting and error codes

Problem Possible Causes What To Do
Dryer doesn't start Dryer is unplugged • Make sure the dryer plug is pushed completely into the outlet.
Fuse is blown/circuit breaker is tripped • Check the house fuse/circuit breaker box and replace fuse or reset breaker. NOTE: Most electric dryers use two fuses/breakers.
Dryer doesn't heat Fuse is blown/circuit breaker is tripped; the dryer may tumble but not heat • Check the house fuse/circuit breaker box and replace both fuses or reset both breakers. Your dryer may tumble if only one fuse is blown or one breaker is tripped.
Gas service is off • Make sure gas shutoff at dryer and main shutoff are fully open.
No heat temperature selected • Select another heat setting.
Dryer shakes or makes noise Some shaking/noise is normal. Dryer may be sitting unevenly • Move dryer to an even floor space, or adjust leveling legs as necessary until even.
Greasy spots on clothes Improper use of fabric softener • Follow directions on fabric softener package.
Drying dirty items with clean ones • Use your dryer to dry only clean items. Dirty items can stain clean items and the dryer.
Clothes were not completely clean • Sometimes stains which cannot be seen when the clothes are wet appear after drying. Use proper washing procedures before drying.
Lint on clothes Lint filter is full • Clean lint screen before each load.
Improper sorting • Sort lint producers (like chenille) from lint collectors (like corduroy).
Static occurs Static electricity can attract lint • See suggestions in this section under Static.
Overloading • Separate large loads into smaller ones.
Paper, tissue, etc., left in pockets • Empty all pockets before laundering clothes.
No fabric softener was used • Try a fabric softener. • Bounce® Fabric Conditioner Dryer Sheets have been approved for use in all GE Dryers when used in accordance with the manufacturer's instructions.
Inconsistent drying times Over-drying • Try a fabric softener.
Synthetics, permanent press and blends can cause static • Adjust setting to Less Dry or Damp Dry.
Type of heat • Automatic drying times will vary according to the type of heat used (electric, natural or LP gas), size of load, types of fabrics, wetness of clothes and condition of exhaust ducts.
The Dry dryness level was chosen but load is still damp Load consists of a mixture of heavy and light fabrics • When combining heavy and light fabrics in a load, choose More Dry if you are using a sensor cycle.
Exhaust system is blocked • Inspect and clean exhaust system.
Privacy Policy