Manual for XWDA 751680

Manual for XWDA 751680

Brand: INDESIT

Category: Washing Machine

Document Type: Manual

Language: EN

Available Languages: EN , ES

Uploaded: April 20, 2026, 8:13 p.m.

Instructions for use

Contents:
Installation (2-3)
Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data

Care and maintenance (4)
Cutting off the water or electricity supply
Cleaning the Washer-Dryer
Cleaning the detergent dispenser drawer
Caring for the door and drum
Cleaning the pump
Checking the water inlet hose

Precautions and tips (5)
General safety
Load balancing system
Disposal

Description of the Washer-Dryer and starting a wash cycle (6-7)
Control panel
Indicator lights
Starting a wash cycle

Wash cycles (8)
Push&Wash+Dry
Table of wash cycles

Personalisation (9)
Setting the temperature
Setting the drying cycle
Wash options

Detergents and laundry (10)
Detergent dispenser drawer
Bleach cycle
Preparing the laundry
Garments requiring special care

Troubleshooting (11)
Service (12)

Troubleshooting and error codes

Problem: Possible causes / Solutions:
The Washer-dryer does not switch on.
  • The appliance is not plugged into the socket fully, or is not making contact.
  • There is no power in the house.
The wash cycle does not start.
  • The Washer-dryer door is not closed properly.
  • The ON/OFF button has not been pressed.
  • The START/PAUSE button has not been pressed.
The Washer-dryer does not take in water (the indicator light for the first wash cycle stage flashes rapidly).
  • The water tap has not been opened.
  • The water inlet hose is not connected to the tap.
  • The hose is bent.
The Washer-dryer continuously takes in and drains water.
  • The water tap has not been opened.
  • There is no water supply in the house.
  • The pressure is too low.
  • The START/PAUSE button has not been pressed.
The Washer-dryer does not drain or spin.
  • The drain hose is not fitted at a height between 65 and 100 cm from the floor (see "Installation").
  • The free end of the hose is under water (see "Installation").
  • The wall drainage system is not fitted with a breather pipe.
  • The wash cycle does not include draining: some wash cycles require the drain phase to be started manually.
  • The drain hose is bent (see "Installation").
  • The drainage duct is clogged.
The Washer-dryer vibrates a lot during the spin cycle.
  • The drum was not unlocked correctly during installation (see "Installation").
  • The Washer-dryer is not level (see "Installation").
  • The Washer-dryer is trapped between cabinets and walls (see "Installation").
The Washer-dryer leaks.
  • The water inlet hose is not screwed on properly (see "Installation").
  • The detergent dispenser drawer is blocked (for cleaning instructions, see "Care and maintenance").
  • The drain hose is not fixed properly (see "Installation").
The "Options" indicator lights and the "start/pause" indicator light flash, while one of the "phase in progress" indicator lights and the "door locked" indicator light will remain lit in a fixed manner.
  • Switch off the machine and unplug it, wait for approximately 1 minute and then switch it back on again.
  • If the problem persists, contact the Technical Assistance Service.
There is too much foam.
  • The detergent is not suitable for machine washing (it should display the text "for Washer-dryers" or "hand and machine wash", or the like).
  • Too much detergent was used.
Push&Wash+Dry does not activate.
  • After switching on the machine a control other than Push&Wash+Dry was activated. Switch the machine off and press the Push&Wash+Dry button.
The washer-dryer does not dry.
  • The appliance is not plugged into the socket, or not enough to make contact.
  • There has been a power failure.
  • The appliance door is not shut properly.
  • All the drying indicator lights are off.
Privacy Policy