Brand: JVC
Category: Audio System
Document Type: Manual
Language: EN
Available Languages: EN , ES
Manual for RX-6010VBK / RX-6018VBK
Uploaded: Nov. 21, 2025, 6:35 p.m.
Warranty Information
JVC warrants this product for 24 months for parts and labor, valid only in the 50 United States, DC, and Puerto Rico.
Basic Operations
- Turning the Power On and Off: Press POWER on the front panel or AUDIO on the remote control. The STANDBY lamp indicates standby mode.
- Selecting the Source to Play: Press the source selecting buttons (DVD, VCR, TV SOUND, CD, TAPE/CDR, FM/AM) on the front panel or remote.
- Adjusting the Volume: Turn the MASTER VOLUME control on the front panel or use the VOLUME +/- buttons on the remote.
- Listening Only with Headphones: Connect headphones to the PHONES jack and press SPEAKERS ON/OFF to turn off the main speakers.
- Muting the Sound: Press MUTING on the remote control. Press again to restore sound.
Troubleshooting and error codes
| PROBLEM | POSSIBLE CAUSE | SOLUTION |
|---|---|---|
| The display does not light up. | The power cord is not plugged in. | Plug the power cord into an AC outlet. |
| No sound from speakers. | Speaker signal cables are not connected. | Check speaker wiring and reconnect if necessary. |
| The SPEAKERS ON/OFF button is not set correctly. | Press SPEAKERS ON/OFF button correctly. | |
| An incorrect source is selected. | Select the correct source. | |
| Muting is activated. | Press MUTING to cancel the mute. | |
| An incorrect input mode (analog or digital) is selected. | Select the correct input mode (analog or digital). | |
| Connections are incorrect. | Check connections. For analog connections, see page 5. For digital connections, see page 7. | |
| Sound from one speaker only. | Speaker signal cables are not connected properly. | Check speaker wiring and reconnect if necessary. |
| The balance is set to one extreme. | Adjust the balance properly (see page 11). | |
| Continuous hiss or buzzing during FM reception. | Incoming signal is too weak. | Connect an outdoor FM antenna or contact your dealer. |
| The station is too far away. | Select a new station. | |
| An incorrect antenna is used. | Check with your dealer to be sure you have the correct antenna. | |
| Antennas are not connected properly. | Check connections. | |
| Occasional cracking noise during FM reception. | Ignition noise from automobiles. | Move the antenna farther from automobile traffic. |
| "OVERLOAD" starts flashing on the display. | Speakers are overloaded because of high volume. | 1. Press POWER on the front panel to turn off the receiver. 2. Stop the playback source. 3. Turn on the receiver again, and adjust the volume. |
| Speakers are overloaded because of short circuit of speaker terminals. | Press POWER on the front panel, then check the speaker wiring. If "OVERLOAD" does not disappear, unplug the AC power cord, then plug it back again. If speaker wiring is not short-circuited, contact your dealer. | |
| "DSP MICON NG" starts flashing on the display. | The built-in microcomputer is not functioning correctly. | Press POWER on the front panel to turn off the receiver. After unplugging the power cord, consult your dealer. |
| The STANDBY lamp lights up after turning on the power, but soon the receiver turns off (into standby mode). | The receiver is overloaded because of a high voltage. | Press POWER on the front panel to turn off the receiver. After unplugging the power cord, consult your dealer. |
| Remote control does not work. | There is an obstruction in front of the remote sensor on the receiver. | Remove the obstruction. |
| Remote control does not operate intendedly. | Batteries are weak. | Replace batteries. |
| An incorrect remote control operation mode is selected. | Select the correct remote control operation mode. (See page 26). |