Brand: JVC
Category: Camcorder
Document Type: Manual
Language: EN
Available Languages: EN , ES
Manual for GY-DV5000
Uploaded: Aug. 10, 2025, 12:36 a.m.
Warranty Information
Refer to your dealer for warranty information.
Basic Operation
Powering On: Set the POWER switch to ON. The unit defaults to Camera mode. Press the MODE switch to change between Camera and VTR modes.
Loading/Unloading Cassette: Set the POWER switch to ON, slide the OPEN knob to open the cassette cover. Insert or eject the cassette. Close the cover when done.
Recording: In Camera mode, press the VTR trigger button to start recording. Press it again to stop.
Playback: In VTR mode, press the PLAY button to start playback. Use FF and REW buttons to fast forward or rewind. Use STILL button to pause or view still frames.
Adjustments: Use dedicated buttons and dials for brightness, contrast, shutter speed, gain, and white balance. Menu screens accessed via the STATUS button allow for deeper settings.
Troubleshooting: Refer to the "Troubleshooting" section for error codes and solutions.
Troubleshooting and error codes
| Symptoms | Remedy |
|---|---|
| Power cannot be switched ON. |
Is power supply connected correctly? Is battery pack recharged? Was the power turned ON immediately after being turned OFF? Wait at least 5 seconds before turning the power ON again once it has been turned OFF. |
| Recording is not possible. |
• Is the switch on cassette set to "REC"? If it is set to "SAVE", set it to "REC". • The Camera mode has not been selected. (The CAM indicator does not light.) While the VTR indicator lights, press the MODE switch upward to turn on the CAM indicator. • The Camera mode has not been selected. (The CAM indicator does not light.) While the VTR indicator lights, camera image will not be output. Press the MODE switch upward to turn on the CAM indicator. |
| Camera image does not appear on LCD monitor or in viewfinder. |
• Adjust the brightness of the LCD monitor or viewfinder screen. • Is the color temperature conversion filter knob set to 5600K+ND? • Is the iris closed? • Is the shutter speed too fast? • Is the viewfinder cable correctly connected? |
| Image shown on LCD monitor or in viewfinder is dark or blurred. |
• In the Camera mode, is "STOP" indicated as the VTR operation mode indicator? When "STBY" is indicated, press the STOP button to display "STOP". • The VTR mode has not been selected. (The VTR indicator does not light.) While the CAM indicator lights, press the MODE switch upward to turn on the VTR indicator. |
| Playback does not start when the play button is pressed. | • Video head may be clogged with dirt. Clean head with the special head cleaning tape. ( See "Precautions for Use of Head Cleaning Tape" on page 8.) |
| DV signal cannot be input. |
• Is the AUDIO SELECT item on the AUDIO/VIDEO menu screen set to CH3/4. To output the sound of the recording, set to CH1/2. |
| Noise interferes with playback video. | Noise appears when playing back a tape When a tape recorded on another unit is played back or used for recording, this phenomenon may occur due to tracking errors. |
| Sound is not output during playback. | The transient section between scenes recorded on other units and those recorded on the GY-DV5000 may appear disturbed. |
| The front section's audio level control doesn't work. | • Is the CH1 FRONT VR item on the AUDIO/VIDEO menu screen set to "DISABLE"? If so, set to "ENABLE". |
| The front section's audio level control doesn't change the audio level of the sound input to CH2. | • The front section's audio level control cannot be used to change the audio level of the sound input to CH2. Use the side section's CH2 audio level control for this purpose. |
| Remaining battery power display is incorrect. |
• The OTHERS (2/2) menu screen's BATTERY TYPE item may not be set correctly in accordance with the type of battery in use. If the menu item setting is incorrect, set it correctly using the OTHERS (2/2) menu screen's item BATTERY TYPE. • Is the battery old? |
| Battery alarm is displayed and the GY-DV5000 enters the non-operating mode even when a fully charged battery is used. | • The capacity of the power supply may be insufficient. Check the power voltage. |
| Cassette cannot be ejected after the power is turned ON. | • Is the TC/UB item on the LCD/VF menu screen set to OFF? If so, set to ON. |
| Time code or user's bits data not displayed. |
• Is the DISPLAY item on the TIME/DATE menu screen set to OFF? Set to ON when the data should be displayed and recorded. To record the data, set the DATE REC item as well. • Is the date and time setting made? See "Setting, Displaying and Recording the Date and Time" on page 41~43. |
| The date and time are not displayed or recorded. |