Manual for JT-SB216JSH-W-E

Manual for JT-SB216JSH-W-E

Brand: MITSUBISHI ELECTRIC

Category: Air Conditioner

Document Type: Manual

Language: EN

Available Languages: EN , ES

Uploaded: Nov. 21, 2025, 6:45 p.m.

Warranty Information

Check the "Date of Purchase" and "Name of Vendor" on the warranty certificate and store it in a safe place.

How to use the appliance

Turning the power on: Open the switch door and turn the power switch to "ON".

After washing hands:

  1. Wet hands.
  2. Insert hands from the side.
  3. Bring hands upwards. Repeat 2-3 times.
  4. Hands are dried.
The dryer stops automatically after 30 seconds. Re-insert hands to continue.

If not using for a long period: Turn the power switch "OFF".

Maintenance

Regularly clean the air filter, drain tank, and drain pipe. Wipe the exterior with a well-wrung cloth.

  • Switch power OFF before cleaning.
  • Clean air filter once a week.
  • Drain and clean drain tank at least once a week.
  • Clean drain pipe at least once a week.

Troubleshooting and error codes

Problem Check Fix
No air blows even if hands are inserted Are any lamps in the display on? Has a blackout occurred? Are you putting your hands in all the way? Was the power switched turned on while your hands or an object was inside the hand drying area? Is the sensor blocked by dirt or dust? Is the black wall area in the hand drying area white with dirt? • Turn the ground-fault circuit interrupter on. • Turn the power switch "ON". • Place your hands all the way inside the hand drying area. • Turn the power switch "OFF", and when the display lamps all go out, remove any foreign substances or dirt. Wait for at least 1 minute after turning the power switch "OFF", and then turn it back "ON" again.
Air does not stop Has the dryer been used continually for more than 30 seconds? Are any lamps in the display flashing? • If the hand dryer is used continually for more than 30 seconds, the power lamp flashes, and the dryer automatically stops. To continue using the hand dryer, remove your hands, and then re-insert them.
Stops operating during hand drying Has the dryer been used continually for more than 30 seconds? Are any lamps in the display flashing? • If the hand dryer is used continually for more than 30 seconds, the power lamp flashes, and the dryer automatically stops. To continue using the hand dryer, remove your hands, and then re-insert them.
Air is cold Air does not warm up The heater lamp is off. (Only for JT-SB216JSH type) Air conditioning is not working. Check the model name of the product. Is the room temperature too high? • Contact the dealer about any changes to the settings. Costs are as agreed with the dealer. • The air may not feel warm if the room temperature is less than 18°C. (The JT-SB216KSN type is not equipped with a simple heater) • The JT-SB216KSN model is not equipped with an internal heater, and therefore hot air does not blow. • If the room temperature is above 30°C, the heater will stop working to prevent the temperature from rising too high.
The lamp does not light up even when the power is switched on. Has a blackout occurred? The ground fault circuit interrupter is "OFF". • Turn the ground-fault circuit interrupter on.
The display section lamp flashes This may flash if there is a malfunction in the power supply. • Turn the power switch "OFF", check that all of the lamps on the display section are off, and then wait for 1 minute before switching the power back "ON".
Crack-like shapes can be seen around the nozzle There is no unevenness, even when touched by hand. (No feeling of cracking) • This pattern occurs when the product is molded (manufactured). It does not affect product performance, and is not a malfunction.
The operating sound is too loud (Air blow is too strong) I want to reduce power consumption (want to turn off the heater) (Only for JT-SB216JSH model) • Contact your dealer for any changes to settings or adjustments etc. Costs are as agreed with the dealer. Cautions • Do not attempt to modify or disassemble this appliance yourself.
Privacy Policy