Brand: Panasonic
Category: Home Theater System
Document Type: Manual
Language: EN
Available Languages: EN , ES
Manual for SC-PT560
Uploaded: Nov. 21, 2025, 9:21 p.m.
Warranty Information
Warranty information is not explicitly stated in the provided pages.
Getting Started
Assemble speakers, connect cables (speakers, audio/video, antenna), connect power.
Setup
Perform QUICK SETUP for language, TV type, and aspect ratio. Preset radio stations.
Disc Playback
Insert disc, select "DVD/CD" source, press Play. Use navigation menus for playback options.
Other Operations
Enjoy radio, Karaoke, VIERA Link, sound effects, and connect to TV or external equipment.
Advanced Features
Connect iPod, play from USB, adjust speaker levels, and use Auto speaker setup.
Troubleshooting and error codes
| Problem | Cause/Solution | Page |
|---|---|---|
| No power. | Insert the AC mains lead securely. | 12 |
| Unit automatically switched to standby mode. | Sleep timer was working and had reached the set time limit. | 16 |
| Display is dark. | Select "BRIGHT" in "FL DIMMER" in the "OTHERS" menu. | 27 |
| "NO PLAY" | You inserted a disc the unit cannot play; insert one it can. You inserted a blank disc. You inserted a disc that has not been finalized. | 27, 36 |
| "NO DISC" | You have not inserted a disc; insert one. You have not inserted the disc correctly; insert it correctly. | 18 |
| "OVER CURRENT ERROR" | The USB device is drawing too much power. Switch to DVD/CD mode, remove the USB and turn the unit off. | 9 |
| "F61" | Check and correct the speaker cable connections. | 9 |
| "F76" | There is a power supply problem. Consult the dealer. | 37 |
| "DVD U11" | Disc may be dirty. Wipe it clean. | 37 |
| "ERROR" | Incorrect operation performed. Read the instructions and try again. PT865 Ensure that necessary preparations have been made before Auto speaker setup. Check and correct the speaker cable connections if you are doing Auto speaker setup. PT865 The volume might be muted. Cancel muting before Auto speaker setup. | 33, 9, 16 |
| "DVD HO” / "DVD FO” stands for a number. | Turn the unit off and then back on. Alternatively, turn the unit off, disconnect the AC mains lead, and then reconnect it. | — |
| "W1" is flashing. | There is no link between the main unit and the wireless system. Check that the wireless system is plugged into the mains socket and is turned on. Ensure that the digital transmitter is fully inserted into the slot of the main unit. | 13, 16, 12 |
| "U70" stands for a number. | The HDMI connection acts unusually. The connected equipment is not HDMI-compatible. Please use HDMI cables that have the HDMI logo. The HDMI cable is too long. The HDMI cable is damaged. | — |
| "REMOTE 1" or "REMOTE 2" | Match the modes on the main unit and remote control. Depending on the number being displayed ("1" or "2"), press and hold [OK] and the corresponding numbered button ([1] or [2]) for at least 2 seconds. | 16 |
| PT865 "NO MIC" | The Auto speaker setup microphone is not inserted. Check whether the Auto speaker setup microphone is plugged in properly into the "SETUP MIC" jack. | 33 |
| PT865 "NOISY" | Excessive ambient noise in the room. Perform the setup again and keep quiet during the Auto speaker setup. | — |
| No response when any buttons are pressed. | This unit cannot play discs other than the ones listed in these operating instructions. The unit may not be operating properly due to lightning, static electricity or some other external factor. Turn the unit off and then back on. Alternatively, turn the unit off, disconnect the AC mains lead, and then reconnect it. Condensation has formed. Wait 1 to 2 hours for it to evaporate. | 36, — |
| No response when remote control buttons are pressed. | Check that the batteries are installed correctly. The batteries are depleted. Replace them with new ones. Aim the remote control at the remote control signal sensor and operate. Change the remote control operating mode. | 13, 17, 16 |
| Other products respond to the remote control. No picture or sound. | Check the video or speaker connection. Check the power or input setting of the connected equipment and the main unit. Check that the disc has something recorded on it. | 9, 10 |
| You have forgotten your ratings password. | While stopped and "DVD/CD" is the source, press and hold [■] (Stop) on the main unit and [≥10] on the remote control until "INITIALIZED” disappears from the TV. Turn the unit off and on again. All settings will return to the default values. | — |
| The VIERA Link "HDAVI Control" function does not respond. | Depending on the condition of this unit or the connected equipment, it may be necessary to repeat the same operation so that the function can work correctly. | 30 |