Manual for FZ-G2 Series

Manual for FZ-G2 Series

Brand: Panasonic

Category: Tablet Computer

Document Type: Manual

Language: EN

Uploaded: Nov. 21, 2025, 6:15 p.m.

Warranty Information

Offers limited hardware and software warranties, with optional extended coverage for accidental damage.

Turning On / Turning Off

Turning On

Press and hold the power switch until the power indicator lights.

Turning Off

Shut down the computer:

  1. Click (Start).
  2. Click (Power) - [Shut down].

Touchpad

Function Operation

  • Move cursor: Move the tip of your finger over the work surface.
  • Click (Tap): Tap a touchpad or press a left button. Right-click: press a right button.
  • Double click (Double tap): Tap a touchpad quickly two times or press a left button quickly two times.
  • Vertical scroll: Trace the right edge of the touchpad vertically with a finger.

Keyboard

Key Combinations

  • Touchpad on/off: ≪Fn≫ + ≪Esc≫
  • LCD brightness: ≪Fn≫ + ≪F1≫ (down) / ≪Fn≫ + ≪F2≫ (up)
  • Display mode switching: ≪Fn≫ + ≪F3≫
  • Speaker on/off: ≪Fn≫ + ≪F4≫
  • Volume: ≪Fn≫ + ≪F5≫ (down) / ≪Fn≫ + ≪F6≫ (up)
  • Modern standby (Sleep): ≪Fn≫ + ≪F7≫
  • Concealed Mode on/off: ≪Fn≫ + ≪F8≫
  • Remaining battery power: ≪Fn≫ + ≪F9≫
  • Airplane Mode on/off: ≪Fn≫ + ≪F10≫
  • Backlit keyboard on/off: ≪Fn≫ + ≪F12≫

Troubleshooting and error codes

Error Message Solution
Cannot start up. The power indicator or battery indicator is not lit. Connect the AC adaptor.
Insert a fully charged battery.
Remove the battery pack and the AC adaptor, and then connect them again.
Even if the AC adaptor and battery pack are correctly connected, if the battery indicator is not lit, the AC adaptor protection function may be operating. Disconnect the AC cord, wait 3 minutes or more, and reconnect the AC cord.
If a device is connected to the USB port, disconnect the device.
Press<Fn> + <F8> or button to turn off the concealed mode.
Cannot turn on the computer. The computer does not resume from sleep. (The power indicator blinks rapidly in green.) Leave it in an environment of 5 °C {41 °F} or higher temperature for about an hour, then turn on the power again.
It takes time for the power indicator to light up. If the power switch is pressed immediately after the battery pack has been mounted on the computer, and while the AC adaptor is not connected, it may take about 5 seconds before the power indicator lights up and the computer turns on. This is because the computer is checking the remaining battery charge; it is not a malfunction.
Remove disks or other media. Press any key to restart If a device is connected to the USB port, disconnect the device, or set [Tablet USB Port] or [Keyboard Base and Cradle USB Port] to [Disabled] in the [Advanced] menu of the Setup Utility.
If the problem persists after removing the disk, it may be a flash memory failure. Contact Panasonic Technical Support.
Windows startup and operation is slow. Start the Setup Utility ( Setup Utility) to return the Setup Utility settings (excluding the passwords) to the default values. Start the Setup Utility and make the settings again. (Note that the processing speed depends on the application software, so this procedure may not make Windows faster.)
If you installed a resident software after purchase, turn off the residence.
Cannot resume. One of the following operations may have been carried out. Press the power switch turn on the computer. Data not saved will be lost.
In sleep mode, the AC adaptor or battery pack was disconnected, or a peripheral was connected or disconnected.
The power switch was pressed for 10 seconds or longer to forcibly turn off the computer.
The battery is exhausted. Sleep and hibernation consumes some power.
Privacy Policy