Name: Manual for LX01
Brand: PIONEER
Availability: InStock

Troubleshooting and error codes

Message	Explanation/Action
Initializing disc. Please wait a moment.	When you load a blank DVD-RW or DVD+RW disc, the recorder automatically initializes it.
Incompatible region number.	The disc loaded has an incompatible region number for the recorder and so will not play.
Cannot record any more titles. No more space for file management data.	The disc control data limit has been reached, or the maximum number of chapters and/or titles has been reached. Erase titles/ chapters or combine chapters.
This disc cannot be recorded. Undo the finalization.	The disc was finalized on a non-Pioneer DVD recorder. Undo the finalization in order to recording/editing.
Cannot play this disc. This disc cannot be recorded. Cannot read the CPRM information. Could not record the information to the disc. Cannot edit. Could not initialize disc. Could not complete finalization successfully. Could not undo finalization successfully. Could not successfully unlock the disc. Incompatible or unreadable disc.	The disc may be dirty or damaged. Take out the disc, clean it and retry. If the error persists, use a new disc. If the error appears even with a new disc, please ask your nearest Pioneer-authorized service center or your dealer to carry out repairs.
Cannot record to a disc that is not CPRM compatible. Cannot record this content using Video mode recording. This video cannot be recorded to DVD+R/+RW.	The video source is copy-once protected. Use a VR mode DVD-R/-RW disc with CPRM for recording.
This content is copy protected.	The video source is copy-protected and cannot be recorded.
Incorrect CPRM information.	The recorder could not read the CPRM information. The recorder may be damaged - please ask your nearest Pioneer-authorized service center or your dealer to carry out repairs.
Repairing disc. Repairing the HDD. Could not repair the disc.	During recording, the power was cut. This display appears when the power is restored. The recorder was unable to repair the disc after a power cut. The contents of the recording will be lost.
Overheating has stopped operation. Press DISPLAY to clear message.	The internal temperature of the recorder has exceeded the operating limit. If this message reappears, please ask your nearest Pioneer-authorized service center or your dealer to carry out repairs.
HDD optimization is recommended. This can be done using Disc Setup. Please perform HDD optimization. This can be done using Disc Setup.	The HDD should be optimized (basically, HDD housekeeping) to maintain playback and recording performance. The HDD is in more urgent need of optimization in order to maintain performance.
The HDD has not been sufficiently optimized. Please optimize again.	If this message appears repeatedly after optimizing the HDD it is likely that there is not enough free space on the HDD for optimization to complete properly. Please erase some titles from the HDD and optimize again.
An error occurred. Please consult the service center. Note that contents on the HDD may be erased when servicing this unit.	This message is displayed when information from the HDD cannot be read. The HDD may be damaged or broken. Please ask your nearest Pioneer-authorized service center or your dealer to carry out repairs.
The Hard Disk Drive info is incorrect. Use the Disc Setup menu to reinitialize.	As the HDD info cannot be properly read, no new recordings can be made. Reinitializing the HDD (page 148) may result in your being able to make recording again. Note that reinitializing the HDD will erase all recorded contents, including protected files.
This signal's TV system is different from the recorder's setting.	The TV system (PAL, NTSC, etc.) of the current channel is different from the TV system settings of this recorder.
Recording failed due to a TV system mismatch. Press DISPLAY to clear message.	The timer recording failed because the TV system of the channel set for recording was different from the setting of the recorder.
Playback has stopped because the TV system is different than the recording.	During recording or timer recording standby, the TV System (PAL, NTSC, etc.) of the playback video changed, causing playback to stop automatically.
You are not allowed to watch this Conditional Access Programme.	A CA module or smart card (obtained from your service provider) is required to watch the selected programme. Insert the supplied module or card into the Common Interface card slot on the front of the recorder (page 17).
There is no DV input or the input signal is unrecordable.	No signal was detected at the DV IN jack. This may appear if a blank section of DV tape is playing in the connected camcorder.
No DV camcorder connected.	The camcorder is not connected properly, or the camcorder is switched off.
You cannot connect more than one DV camcorder at a time.	This recorder's DV jack supports connection to just one camcorder.
Cannot operate the DV camcorder. Could not operate the DV camcorder. The DV camcorder is not set for playback. Please select playback mode on the DV camcorder.	This recorder cannot operate the DV camcorder. Try switching off the camcorder then turn it back on again. This recorder was not able to operate the DV camcorder. The camcorder is in camera mode. Switch it to playback mode.
The printer is not ready or is not connected. Please check the printer.	This message is displayed when communication could not be established with the printer. See the Troubleshooting section if you do not know the cause.
Printing has been cancelled because ...	This message is displayed when there is a printer error during printing. After checking the printer for the cause of the error, either reconnect the printer and start the printing job again, or select "Yes" to resume printing (select "No" to cancel the print job). See also the operating instructions that came with your printer for possible causes of print errors.

Manual for LX01

Warranty Information

Basic Operation

Troubleshooting and error codes