Brand: SHARP
Category: Audio
Document Type: Manual
Language: EN
Available Languages: EN , ES
Manual for HT-SB35D
Uploaded: Nov. 21, 2025, 8:50 p.m.
Warranty Information
One year parts and labor warranty from the date of purchase for the original purchaser.
Basic Operation Summary
Power On/Off: Press the ON/STANDBY button on the main unit or remote control. The indicator lights up based on the input source.
Input Selection: Press the INPUT button to cycle through available sources (Optical In, Audio In, Bluetooth). The corresponding indicator color (green, cyan, blue) will show the selected input.
Volume Control: Use the VOLUME +/- buttons on the main unit or VOL +/- buttons on the remote to adjust the sound level.
Sound Modes: Select desired sound effects like CINEMA, MUSIC, NEWS, or BYPASS using the respective buttons on the remote control.
Bluetooth Connectivity: For initial pairing, use NFC by tapping your device to the detection area or use the manual pairing procedure via the PAIRING button. Once paired, playback can be initiated.
Subwoofer Control: Adjust the subwoofer level using the SW LEVEL +/- buttons on the remote control.
Muting: Press the MUTE button on the remote to temporarily silence the audio. Press again to restore.
Troubleshooting and error codes
| Symptom | Possible cause |
|---|---|
| No sound is heard. | Is the input signal (selection) set properly? |
| Is the volume level set to minimum? | |
| Is muting activated? | |
| Are the connections made correctly? | |
| Noise is heard during playback. | Move the sound bar away from any computers or mobile phones. |
| Sound is distorted. | TV output sound is distorted. Reduce the TV volume or sound bar volume. |
| When a button is pressed, the sound bar does not respond. | Set this sound bar to the standby mode and then turn it back on. If the sound bar still malfunctions, reset it. (Refer to "Factory reset, clearing all setting".) |
| The power is not turned on. | Is the sound bar unplugged? (Refer to page 7.) The protection circuit may be activated. Unplug and plug in the power cord again after 5 minutes or more. |
| No sound is heard at subwoofer. | Is the AC for subwoofer plugged in? The subwoofer is not connected with the sound bar. Is the sound bar in mute? If the subwoofer still malfunctions, reconnect it to the sound bar. (Refer page 9.) |
| NFC / Bluetooth | Symptom: NFC-enabled device cannot connect to Bluetooth via NFC tag. Possible cause: Main unit is not in Bluetooth pairing mode. Perform "NFC connection for audio playback". (Refer page 12.) |
| Symptom: No sound is heard. Possible cause: Is the sound bar too far from the Bluetooth stereo audio source device? Is the sound bar paired with the Bluetooth stereo audio source device? Is the Bluetooth stereo audio source device in playback condition? Is a headphone plugged to the Bluetooth stereo audio source device? Is the sound bar too near to a device that generates electromagnetic radiation? Is there any obstacle between the sound bar and the Bluetooth stereo audio source device? |
|
| Symptom: Bluetooth sound is interrupted or distorted. Possible cause: (Same as above, generally related to distance, interference, or pairing issues) |
|
| Remote control | Symptom: The remote control does not operate properly. Possible cause: Is the battery polarity correct? Is the battery dead? Is the distance or angle incorrect? Are there any obstructions in front of the sound bar? Is there a strong light shining on the remote sensor? Is the remote control for another equipment used simultaneously? |
| Symptom: The sound bar cannot be turned on with the remote control. Possible cause: Is the AC power cord of the sound bar plugged in? Is the battery inserted? Has the plastic shield at the remote control battery holder been removed? |
|
| Condensation Sudden temperature changes, storage or operation in an ex-tremely humid environment may cause condensation inside the cabinet or on the transmitter on the remote control. Condensation can cause the sound bar to malfunction. If this happens, leave the power on until normal operation is possible (about 1 hour). Wipe off any condensation on the transmitter with a soft cloth before operating the sound bar. |
|
| Factory reset, clearing all setting | Make sure to disconnect all audio input cables attached to the sound bar before performing the factory reset. 1. Press ON/STANDBY button to enter the power standby mode. 2. While pressing down the PAIRING button on the main unit, press the ON/STANDBY button. 3. Press the ON/STANDBY button again. (Subwoofer Pairing indicator will turn blue.) Caution: This operation will erase all data stored in memory. |