Manual for HT-SB60

Manual for HT-SB60

Brand: SHARP

Category: Audio

Document Type: Manual

Language: EN

Available Languages: EN , ES

Uploaded: Nov. 21, 2025, 6:44 p.m.

Warranty Information

This Sharp product is warranted against faults in material and manufacture for 12 months.

Turning On/Off: Press the ON/STAND-BY button on the sound bar or remote. The system enters standby mode when the button is pressed again (subwoofer indicator turns red). The system may also turn on automatically if connected via HDMI CEC.
Sound Modes: Press the SOUND MODE button on the unit or desired sound mode button on the remote (CINEMA, MUSIC, GAME, SPORT, NEWS, NIGHT, BYPASS) to select sound effects.
Volume Control: Use the VOLUME + / - buttons on the unit or VOL +/- buttons on the remote to adjust volume. Press MUTE on the remote to temporarily silence the sound; press again to restore.
Subwoofer Level: Use the SW LEVEL buttons on the remote to adjust the subwoofer's output.
Connections: Connect devices via HDMI (TV ARC, HDMI 1, HDMI 2), Optical, or Audio IN. Ensure correct cables and settings are used.

Troubleshooting and error codes

Symptom Possible cause
General
No sound is heard.
  • Is the input signal (selection) set properly?
  • Is the volume level set to "Min"?
  • Is muting activated?
  • Is HDMI compliant equipment being used?
  • Is the HDMI cable connected correctly?
  • Connect the HDMI cable correctly and then perform the reset procedure. (refer this page)
  • Do not connect or disconnect an HDMI cable whilst power is on. This may lead to operation problems.
The sound from subwoofer is not well balanced. Is the subwoofer level set to the minimum or maximum level?
Power turns off suddenly.
  • Is the HDMI cable connected correctly? Connect the HDMI cable correctly and then perform the reset procedure.
  • Move the speaker away from any computers or mobile phones.
Noise is heard during playback. Set the sound bar to the stand-by mode and then turn it back on.
When a button is pressed, the sound bar does not respond.
  • Is the sound bar unplugged?
  • The protection circuit may be activated. Unplug and plug in the power lead again after 5 minutes or more.
The power is not turned on.
  • Is the sound bar unplugged?
  • The protection circuit may be activated. Unplug and plug in the power lead again after 5 minutes or more.
3D images not displayed on the TV.
  • Depending on the TV and Video component, 3D images may not be displayed. Check the operation manual of the respective component.
  • HDMI cable not support 3D image.
Background noise appears when connecting with RCA audio output terminal connection from a TV-set/ DVD/Blu-ray Disc Player.
  • Please change to HDMI/ARC or headphone terminal from TV-Set/DVD/Blu-ray Disc Player. This effect may occur depending on TV/DVD/Blu-ray Disc Player-Brand, model and age, and it is not the sound bar problem.
Wireless connection cannot be established.
  • Check the distance between the sound bar and subwoofer (less than 10m (32 feet)).
  • Make sure there is no other wireless devices near the unit.
  • Make sure there is no obstacles (especially metal) blocking between the sound bar and subwoofer.
  • Manually re-link the sound bar and subwoofer (refer page 10).
Remote control
The remote control does not operate properly.
  • Is the battery polarity correct?
  • Is the battery dead?
  • Is the distance or angle incorrect?
  • Are there any obstructions in front of the sound bar?
  • Is there a strong light shining on the remote sensor?
  • Is the remote control for another equipment used simultaneously?
The sound bar cannot be turned on with the remote control.
  • Is the AC power lead of the sound bar plugged in?
  • Is the battery inserted?
Privacy Policy