Manual for LAM8675 - Troubleshooting and error codes + PDF Download

Manual for LAM8675 - Troubleshooting and error codes + PDF Download

Brand: LAMONA

Category: Dishwasher

Manual Type:

Language:

Uploaded: April 8, 2025, 1:44 p.m.

Manual Publish Date: 2019-01-01

Warranty Summary

Your LAMONA appliance has a manufacturer's guarantee covering breakdown repairs, details of which are on your Proof of Purchase Document.
Download Manual
Daily Use Summary:
  • 1. Check Water Connection: Ensure dishwasher is connected to water and tap is open.
  • 2. Switch On: Open door and press the ON/OFF button.
  • 3. Load Racks: Load dishes into the racks properly.
  • 4. Detergent Dispenser: Fill the detergent dispenser.
  • 5. Choose Program: Select program based on crockery type and soiling.
  • 6. Start: Close the door to start the wash cycle.
  • 7. End of Cycle: Open door after cycle ends and switch off.

Troubleshooting and error codes

PROBLEMS POSSIBLE CAUSES SOLUTIONS
The dishwasher won't start or does not respond to commands. The appliance has not been plugged in properly. Insert the plug into the socket.
Power outage. The dishwasher starts automatically when the power returns.
The dishwasher door is not closed. Firmly push the door until you hear the "click".
It does not respond to commands. Switch off the appliance by pressing the ON/OFF button, switch it back on after approximately one minute and reset the program.
The door doesn't lock. Racks are not fully pushed in. Verify that racks are fully pushed in.
The door is not locking. Firmly push the door until you hear the "clack" sound.
The dishwasher won't drain. The wash cycle has not finished yet. Wait until the wash cycle finishes.
The drain hose is bent. Check that the drain hose is not bent (see INSTALATION INSTRUCTION).
The sink drain pipe is blocked. Clean the sink drain pipe.
The filter is clogged up with food residues. Clean the filter (see CLEANING THE FILTER ASSEMBLY).
The dishwasher makes excessive noise. The dishes are rattling against each other. Position the crockery correctly (see LOADING THE RACKS).
An excessive amount of foam has been produced. The detergent has not been measured out correctly or it is not suitable for use in dishwashers (see FILLING THE DETERGENT DISPEN-SER). Reset the current cycle by switching OFF the dishwasher, then switch it on again, select a new program, press START and close the door. Please do not add any detergent.
The dishes have not been dried. The selected program hasn't any drying phase. Verify on the programs table if the selected program has the drying phase.
The rinse aid has run out or the doseage is not adequate. Add the rinse aid or adjust the dosage levels higher (see FILLING THE RINSE AID DISPENSER).
The dishes are made of non-stick or plastic. The presence of drops is normal (see TIPS).
The dishes are not clean. The crockery has not been arranged properly. Arrange the crockery correctly (see LOADING THE RACKS).
The spray arms cannot rotate freely, being hindered by the dishes. Adjust the rack height (see LOADING THE RACKS).
The wash cycle is too gentle. Select an appropriate wash cycle (see PROGRAMS TABLE).
An excessive amount of foam has been produced. The detergent has not been measured out correctly or it is not suita-ble for use in dishwashers (see FILLING THE DETERGENT DISPENSER).
The cap on the rinse aid compartment has not been shut correctly. Make sure the cap of the rinse aid dispenser is closed.
The filter is soiled or clogged. Clean the filter assembly (see CARE AND MAINTENANCE).
There is no salt. Fill the salt reservoir (see FILLING THE SALT RESERVOIR).
The dishwasher does not fill with water. No water in the water supply or the tap is closed. Make sure there is water in the water supply and the tap is open.
The inlet hose is bent. Un-kink hose and ensure water is turned on
The sieve in the water inlet hose is clogged. Turn off water, remove fill hose, clean filter, refit hose and turn water back on. After that, turn off and turn on the dishwasher and restart the program.
The dishes and glasses show a whitish film. The salt level is too low. Fill the salt reservoir (see FILLING THE SALT RESERVOIR).
The adjustment of the water hardness is not adequate. Increase the values (see WATER HARDNESS TABLE).
The cap of the salt reservoir is not properly closed. Check the salt cap is correctly fitted and closed.
The rinse aid is used up or the dosage is insufficient. Add the rinse aid or adjust the dosage levels higher.
The dishes and glasses are blue streaked or have a bluish tinge. The rinse aid dosage is excessive. Adjust the dosage rates below.

Troubleshooting and error codes

PROBLEMS POSSIBLE CAUSES SOLUTIONS
The dishwasher won't start or does not respond to commands. The appliance has not been plugged in properly. Insert the plug into the socket.
Power outage. The dishwasher starts automatically when the power returns.
The dishwasher door is not closed. Firmly push the door until you hear the "click".
It does not respond to commands. Switch off the appliance by pressing the ON/OFF button, switch it back on after approximately one minute and reset the program.
The door doesn't lock. Racks are not fully pushed in. Verify that racks are fully pushed in.
The door is not locking. Firmly push the door until you hear the "clack" sound.
The dishwasher won't drain. The wash cycle has not finished yet. Wait until the wash cycle finishes.
The drain hose is bent. Check that the drain hose is not bent (see INSTALATION INSTRUCTION).
The sink drain pipe is blocked. Clean the sink drain pipe.
The filter is clogged up with food residues. Clean the filter (see CLEANING THE FILTER ASSEMBLY).
The dishwasher makes excessive noise. The dishes are rattling against each other. Position the crockery correctly (see LOADING THE RACKS).
An excessive amount of foam has been produced. The detergent has not been measured out correctly or it is not suitable for use in dishwashers (see FILLING THE DETERGENT DISPEN-SER). Reset the current cycle by switching OFF the dishwasher, then switch it on again, select a new program, press START and close the door. Please do not add any detergent.
The dishes have not been dried. The selected program hasn't any drying phase. Verify on the programs table if the selected program has the drying phase.
The rinse aid has run out or the doseage is not adequate. Add the rinse aid or adjust the dosage levels higher (see FILLING THE RINSE AID DISPENSER).
The dishes are made of non-stick or plastic. The presence of drops is normal (see TIPS).
The dishes are not clean. The crockery has not been arranged properly. Arrange the crockery correctly (see LOADING THE RACKS).
The spray arms cannot rotate freely, being hindered by the dishes. Adjust the rack height (see LOADING THE RACKS).
The wash cycle is too gentle. Select an appropriate wash cycle (see PROGRAMS TABLE).
An excessive amount of foam has been produced. The detergent has not been measured out correctly or it is not suita-ble for use in dishwashers (see FILLING THE DETERGENT DISPENSER).
The cap on the rinse aid compartment has not been shut correctly. Make sure the cap of the rinse aid dispenser is closed.
The filter is soiled or clogged. Clean the filter assembly (see CARE AND MAINTENANCE).
There is no salt. Fill the salt reservoir (see FILLING THE SALT RESERVOIR).
The dishwasher does not fill with water. No water in the water supply or the tap is closed. Make sure there is water in the water supply and the tap is open.
The inlet hose is bent. Un-kink hose and ensure water is turned on
The sieve in the water inlet hose is clogged. Turn off water, remove fill hose, clean filter, refit hose and turn water back on. After that, turn off and turn on the dishwasher and restart the program.
The dishes and glasses show a whitish film. The salt level is too low. Fill the salt reservoir (see FILLING THE SALT RESERVOIR).
The adjustment of the water hardness is not adequate. Increase the values (see WATER HARDNESS TABLE).
The cap of the salt reservoir is not properly closed. Check the salt cap is correctly fitted and closed.
The rinse aid is used up or the dosage is insufficient. Add the rinse aid or adjust the dosage levels higher.
The dishes and glasses are blue streaked or have a bluish tinge. The rinse aid dosage is excessive. Adjust the dosage rates below.